Global-CE > Grader > Cat Grader > CAT Cat®16M3 Motor grader
CAT Cat®16M3 Motor grader

CAT Cat®16M3 Motor grader

Mass of complete machine (kg):
32411.0
Engine model:
Cat® C13 ACERT™ VHP
Rated power (KW):
216
View Complete Details

Product Feature

Product Parameter


Engine
Basic power(1st gear)- Net power 216.0 kW
Engine model Cat® C13 ACERT™ VHP
Cylinder bore 130.0 mm
Stroke 157.0 mm
Speed at rated power 2000 rpm
VHP Range – Net worth 216-259 kW(290-348 hp)
VHP Range – Net worth(The metric system) 216-259 kW(294-353 hp)
Power derated altitude:Tier 2/Stage II/Japan 2001(Tier 2)Equivalent standard 3954.0 m
Power derated altitude:Tier 3/Stage IIIA/Japan 2006(Tier 3)Equivalent standard 3711.0 m
Power derated altitude:Tier 4/Stage IV/Japan 2014(Tier 4) 3810.0 m
Basic power(1st gear)– Net worth(The metric system) 216.0 kW
Torque reserve:Tier 2/Stage II/Japan 2001(Tier 2)Equivalent standard 39%
Torque reserve:Tier 3/Stage IIIA/Japan 2006(Tier 3)Equivalent standard 39%
Torque reserve:Tier 4/Stage IV/Japan 2014(Tier 4) 43%
Discharge (1) America EPA Tier 4 Final/European Union Stage IV/Japan 2014(Tier 4 Final)
Discharge (2) Tier 3/Stage IIIA/Japan 2006(Tier 3)Equivalent emission standards – Depending on the particular country/Emission standards for the region
Discharge (3) Tier 2/Stage II/Japan 2001(Tier 2)Equivalent emission standards – Depending on the particular country/Emission standards for the region
Maximum torque - ISO 9249:Tier 2/Stage II/Japan 2001(Tier 2)Equivalent emission standards 1721.0 N·m
Maximum torque - ISO 9249:Tier 3/Stage IIIA/Japan 2006(Tier 3)Equivalent emission standards 1721.0 N·m
Maximum torque - ISO 9249:Tier 4/Stage IV/Japan 2014(Tier 4) 1771.0 N·m
Standard - Environmental tolerance 50.0 °C
Standard – Fan speed:Lowest 550 rpm
Standard – Fan speed:Highest 1450 rpm
Optimized VHP The scope of – Net worth 216-259 kW(290-348 hp)
Displacement 12.5 l
Number of cylinders 6
Power train
Forward/Reverse gear 8 forward gears/6 reverse gears
Gearbox Direct drive,Power shift,Intermediate shaft
Brake - Parking Spring-type hydraulic release
Brake - Repair Oil start type,Oil bath pan
Brake - Assist Oil start type,Oil-immersed disc type
Brake – Dynamic braking torque per wheel 36701.0 N·m
Hydraulic system
Loop type Closed Center Electro-Hydraulic Load Sensing
Pump type Variable Piston
Maximum system pressure 24750.0 kPa
Standby pressure 5900.0 kPa
Notice *At 2150 rpm rpm Measured pump displacement at。
Pump displacement* 280.0 l/min
Operating specifications
Back a car - 1st gear 3.6 km/h
Back a car - Second gear 6.6 km/h
Back a car - Third gear 9.7 km/h
Back a car - Fourth gear 15.0 km/h
Back a car - Fifth gear 28.0 km/h
Back a car - 6th gear 40.8 km/h
Forward - 1st gear 4.5 km/h
Forward - Second gear 6.1 km/h
Forward - Third gear 8.9 km/h
Forward - Fourth gear 12.3 km/h
Forward - Fifth gear 19.0 km/h
Forward - 6th gear 25.8 km/h
Forward - Seventh gear 35.5 km/h
Forward - 8th gear 51.7 km/h
Top speed - Back a car 40.8 km/h
Top speed - Forward 51.7 km/h
Steering range - Left/Right 47.5°
Turning radius(Outside of front wheel) 9.3 m
Articulation angle – Left/Right 20°
Service fill
Fuel capacity 496.0 l
Cooling system 70.0 l
DEF Box 16.0 l
Hydraulic system - Totally 146.0 l
Hydraulic system - Fuel tank 70.0 l
Engine oil 36.0 l
Gearbox/Differential/Final drive 98.5 l
Two-wheel set housing(Each) 129.0 l
Front wheel spindle bearing housing 0.9 l
Circle drive box 10.0 l
Rack
Front frame structure - Width 356.0 mm
Front frame structure - Height 460.0 mm
Front frame structure – Thickness 14.0 mm
Front axle - Total swing on each side 35°
Front axle - Height to center 670.0 mm
Front axle – The wheel is tilted Left 18°/Right 17°
Rotary disk - Blade beam thickness 50.0 mm
Rotary disk- Diameter 1822.0 mm
Drawbar - Width 76.0 mm
Drawbar - Height 203.0 mm
Moldboard
Blade width 4.9 m
Arc radius 413.0 mm
Dento-laryngeal space 126.0 mm
Downforce – Basic GVW 13945.0 kg
Downforce – Max GVW 19895.0 kg
Stop Bit - Thickness 19.0 mm
Stop Bit - Width 152.0 mm
Thickness 25.0 mm
Blade pull* - Basic GVW 18615.0 kg
Blade pull* - Max GVW 23985.0 kg
Spade edge - Thickness 25.0 mm
Spade edge - Width 203.0 mm
Range of blade movement
Blade maximum roll angle 65°
Maximum lifting height above ground 400.0 mm
Maximum depth of cut 470.0 mm
Maximum blade length out of tire - Right side 2311.0 mm
Maximum blade length out of tire - Left side 2311.0 mm
Moldboard sidesway - Right side 790.0 mm
Moldboard sidesway- Left side 740.0 mm
The circle center is displaced - Right side 560.0 mm
The circle center is displaced - Left side 690.0 mm
Blade tip range - Forward 40°
Blade tip range - Backwards
Ripper
Maximum depth of ripping 452.0 mm
Rack carrier spacing – Minimal 445.0 mm
Rack carrier spacing – Max 500.0 mm
Ripper rack 7
Penetration 13749.0 kg
Digging force 19822.0 kg
Increase in machine length when the beam is raised 1610.0 mm
Weight
Operating weight - Typical configuration 32411.0 kg
Size(Approximation)
Ground clearance at rear axle 396.0 mm
Width - Outside of front tire 3411.0 mm
Width - Outside of rear tire 3411.0 mm
Width - Tire centerline 2703.0 mm
Height to exhaust pipe 3557.0 mm
Height to top of cylinder 3088.0 mm
Length - Front tire to rear of machine(Includes a traction hinge) 10593.0 mm
Length - Front axle to moldboard 3066.0 mm
Length - Front axle to tandem centre 7365.0 mm
Length - Axle spacing of double wheel set 1841.0 mm
Length - Counterweight to Ripper 12051.0 mm
Height - Center of front axle 733.0 mm
Height - The top of the cab 3719.0 mm
Standard
ROPS/FOPS ISO 3471:2008/ISO 3449:2005
Brake ISO 3450:2011
Noise ISO 6394:2008/ISO 6395:2008/ISO 6396:2008
Turn ISO 5010:2007
Double wheel set
Width 4.9 m
Height 787.0 mm
Side wall thickness - Inside 22.0 mm
Side wall thickness - External 22.0 mm
The double wheel set swings - Front up 15°
The double wheel set swings - Front down 25°
Drive chain pitch 63.5 mm
Axle spacing 1841.0 mm
Variable power
Gear:Forward - 1st gear 216.0 kW
Gear:Forward - Second gear 216.0 kW
Gear:Forward - Third gear 222.0 kW
Gear:Forward - Fourth gear 227.0 kW
Gear:Forward - Fifth gear 232.0 kW
Gear:Forward - 6th gear 239.0 kW
Gear:Forward - Seventh gear 244.0 kW
Gear:Forward - 8th gear 259.0 kW
Gear:Back off - 1st gear 216.0 kW
Gear:Back off - Second gear 216.0 kW
Gear:Back off – Gear 3 to 6 222.0 kW
Weight TIER 4/STAGE IV/Japan 2014(TIER 4 FINAL)
Notice (1) *If the machine is not equipped with Tier 4 Final Emission standard engine,150 shall be subtracted from the rear axle weight and the total weight kg(331 lb)。
Notice (2) **Base operating weight is based on standard machine configuration,Including 23.5 R25 tires、Full tank、Operator and ROPS Cab。
Gross vehicle weight - Basic weight**:Total 28816.0 kg
Gross vehicle weight - Maximum measured weight:Front axle 11850.0 kg
Gross vehicle weight - Maximum measured weight:Rear axle 26650.0 kg
Gross vehicle weight – Typical configuration:Front axle 8733.0 kg
Gross vehicle weight – Typical configuration:Rear axle 23678.0 kg
Gross vehicle weight – Typical configuration:Total 32411.0 kg
Gross vehicle weight – Basic weight**:Front axle 8134.0 kg
Gross vehicle weight – Basic weight**:Rear axle 20682.0 kg
Gross vehicle weight – Maximum measured weight - Total 38500.0 kg
Optional tire configuration
Wheel set:19.5×25 MP (1) Tire:23.5R25 Bridgestone VKT 2 Star
Wheel set:19.5×25 MP (2) Tire:23.5R25 Bridgestone VKT 1 Star
Wheel set:19.5×25 MP (3) Tire:23.5R25 Bridgestone VJT 1 Star
Wheel set:19.5×25 MP (4) Tire:23.5R25 Michelin XHA 2 Star
Wheel set:19.5×25 MP (5) Tire:23.5R25 Michelin XLDD 2 Star L5

Send Inquiry

Connect with Cat
I want quotes for
Email ID
Your Country is
Please select
Name
Phone Number
- -
SUBMIT
Connect with Cat
I want quotes for
Email ID
Your Country is
Please select
Name
Phone Number
- -
SUBMIT

Related products that may lnterest you

Grader related brands

Copyright Notice © 2002-2024 global-ce.com