CAT Cat®AP600F Asphalt paver
Product Feature
●Fuel efficient and quiet
CAT C7.1 Engine
C7.1 engine available at 2200 rpm 151 is available below kW(205 hp)The power of,In line with the United States EPA Tier 3 and EU Stage IIIA Equivalent emission standards。
Fuel saving mode
1650 is used in fuel-saving mode rpm Engine speed of,And Cat E Fuel consumption is reduced by up to 5% compared with the series paver%,While further reducing the noise level.。
Automatic control function of engine speed
When automatic engine speed control is enabled,The engine speed will decrease to 1000 when the propel lever is moved into neutral rpm Idle speed,Or 1300 when screed heating is enabled rpm。
Advanced Fuel Economy Mode
The simultaneous activation of Economy Mode and Automatic Engine Speed Control changes the engine speed according to the load factor。 If enabled,The engine will be paved at 1650 rpm Run at the speed of。 If the upper power limit is exceeded,The engine speed will increase to 2200 rpm And remain unchanged.,Until the demand falls below the upper limit for 30 second,This ensures reliable performance。
●Quick starting device
Quiet heating
Quiet heating mode at 1300 rpm Operate at engine speed of,And provide heating within 15 minute。
Fast heating
When equipped with 10.0 m(33')When paving kit wide,Rapid heating mode provides heating in 35 minutes。
Temperature range
Three preset heating options provide a wide range of temperatures for various mix designs;The low temperature is 110°C Or 230°F,The medium temperature is 130°C Or 266°F,The high temperature is 160°C Or 320°F。
●More comprehensive control
The view is wider,Better comfort
Dual independent operator stations can extend out of the rack,Have a good all-round view。 Compact front-loading cooling system improves forward visibility,The redesigned auger assembly optimizes the visibility of the material height in front of the screed。 Heated seat option、Seat multi-way adjustment and tilt console,Keep operators comfortable throughout the day。 In addition,The top-mounted cooling system can make the smoke、Keep hot air and fan noise away from cooler operator,And provide a quieter working environment。
Smoke management system
Proprietary ventilation system draws smoke out of the conveyor tunnel and auger chamber,Keep it away from the operator,This creates a more comfortable working environment for the operator。
●Waterproof display
One-touch operation
By mean of a feeding system for automatic refilling、One-touch function for feed system activation and hopper control,Operators are able to focus on truck rotation and other work,So that that efficiency is improve。
Simple technology
Technology helps operators perform better。 Intuitive symbols and large graphics simplify operation,But through interactivity LCD The display accesses the generator start、Screed temperature control and mix height adjustment,And that efficiency is improve。
●Improve efficiency
Automatic filling type feeding system
Allows the conveyor and auger to work alternately,Until the mixture height reaches the sensor set point,Thus simplifying start-up。
One-touch feeding system
Automatic start of the entire feeding system by means of a single button,More efficient。
Single Touch Hopper Control
Just touch the button and release it,Hopper wing plate and hydraulic hopper door can be folded。 The system can be customized,In order to activate the left or right wing separately or simultaneously、Or hydraulic front hopper door。
Cleaning and preheating mode
This function starts the auger at a low speed、Conveyor and tamper bar(If equipped),Ability to spray release agent to prevent material build up。
Mixture height adjustment
When needed,From the tractor LCD Change the mix height in front of the screed on the display,Thereby increasing versatility.。
Hydraulic main frame extension plate
Optional 457 mm(18")The hydraulic main frame extension plate is attached to the auger assembly,The material can smoothly flow to the expander.。 When reducing the paving width,They can be retracted with the screed extension。
Multi-feed sensor option
The feeding system can be customized,For automatic operation without or with 2 or 4 feed sensor。 When paving without sensors due to failure,Simply set the feed system to“Automatic”And adjust that setting of the mixture height,Eliminates the need to cycle manual switches as in previous model。
Maintenance is more convenient
Base plate without fasteners simplifies replacement,The bottom side fasteners of the chain guard prevent bolt wear and material accumulation,And is convenient to replace。
●Wheeled undercarriage
Power steering system
There is a position sensor in the left-hand steering cylinder,The driving speed of the travel motor can be adjusted according to the steering angle of the front wheel,Helps maintain consistent ground speed when steering。 This unique system results in better mat quality and reduced wear on the drive system。
Four-wheel drive
Provides power to front bogie wheel,Thereby providing additional traction.。 Dedicated pump provides a 50% increase in torque over previous model%。
All-wheel drive
For the former、Powered by rear bogie wheels。 Up to 200% more traction than previous model%。
●SE Series screed
Screed heating technology
Proprietary temperature zone monitoring allows heating to continue in the event of a temperature sensor failure。 The system also monitors the failure of the heating element,Eliminates unnecessary replacement。
Easily adjusted
The screed's feed system rate adjustment provides versatility。 Extender height、Standard hydraulic adjustment for grade and camber,Allows adjustment during driving at standard and maximum paving width。
Two-speed proportional expander control
Proprietary two-speed proportional expander control,Speed can be reduced when paving width is extended,So that accurate control and quick reaction can be carry out around an obstacle。
Better efficiency
The heating element can slide out,Easy to replace,No need to remove the screed。 Machined screed frame simplifies screed replacement and leveling。
Tamper screed option
Screed with tamper bar for increased density,Because it causes the material to gather under the screed。 2 mm、4 mm And 7 mm Three stroke settings provide versatility,And has 700 to 1800 rpm Variable tamper bar speed range。
Wide paving kit
Proprietary power control simplifies adjustment across paving width,Better texture and quality of the mat can be obtained。 Innovative design uses spreader slope to connect wide paving kits,No additional lifting equipment is required。
●CAT Grade Control
The operation is simple
F Series pavers can be operated from either of two tractor or two screed console Cat Grade Control。 Split screen mode can be set to monitor each side of the screed,To allow a single person to monitor the operation。
Precise control
The control is more precise,And that utilization rate of the mixture is improve to the maximum extent.,And that cost is save。 By an acoustic wave sensor using 5 sensor,Discard two readings and average the remaining three reading,Thus achieving a true average。 10-point automatic calibration,Eliminates single calibration point overshoot/Too low problem。 Cross connections are used,Adjust the height to keep the slope and elevation constant。 Real 9 m(30')Sonic Balance Bar,You can make the movement of the tow point account for 1% of the total slope deviation/3。
Highly reliable
Waterproof display、Factory-installed components and consistent wiring provide excellent performance。 The sealing components are heat resistant、Damp-proof and vibration-proof,Built-in temperature sensor has better reliability than shackle type sensor。
Product Parameter
Weight |
|
Operating weight - Paver only |
13845 kg |
Operating weight - Only SE60 V Screed |
3400 kg |
Operating weight - Only SE50 VT Screed |
3340 kg |
Operating weight - Only SE50 V Screed |
3284 kg |
Shipping weight - Paver only |
13558 kg |
Operating specifications |
|
Inside turning radius |
1.5 m |
Maximum paving speed - Screed with tamper bar |
25 m/min |
Standard paving range - SE60 V |
3.0-6 m(9' 10" - 19' 6") |
Maximum paving width - SE60 V Screed |
7.65 m |
Working specifications |
|
Standard paving range - SE50 V、SE50 VT |
2.55 - 5 m(8'4" - 16'4") |
Maximum paving speed - With vibrating screed |
76 m/min |
Maximum travel speed |
14.9 km/h |
Maximum throughput capacity |
1300 tonnes/hr |
Maximum paving width - SE50 VT |
8 m |
Maximum paving width - SE50 V |
6.5 m |
Hopper capacity |
7.1 m³ |
Engine |
|
Total power |
151 kW |
ENGINE |
|
Engine model |
Cat C7.1 |
SERVICE REFILL CAPACITIES |
|
Fuel tank capacity |
278 l |
Service refill capacity |
|
DEF Box |
19.1 l |